5V 30leds/m White color Digital WS2812 LED Strips GL-FBWS2812W30M10W5

1.WS2812 SMD5050 Digital LED Strip ,DC5V,30led/m,magic 1800K~10000K digital,SDCM<5;

2.Indoor lighting IP20 and outdoor lighting IP65&IP67&IP68;

3.From 4.8w to 18w adjustable wattage;

4. With standard 3M self-stick , easy for installation;

5. CE Certificated and RoHS compliant;

6. Factory wholesale cost.OEM and ODM service.

WS2812 is a intelligent control LED light source that the control circuit and RGB chip are integrated in a package of 5050 components. It internal include intelligent digital port data latch and signal reshaping amplification drive circuit. Also include a precision internal oscillator and a 12V voltage programmable constant current control part, effectively ensuring the pixel point light color height consistent.The data transfer protocol use single NZR communication mode. After the pixel power-on reset, the DIN port receive data from controller, the first pixel collect initial 24bit data then sent to the internal data latch, the other data which reshaping by the internal signal reshaping amplification circuit sent to the next cascade pixel through the DO port. After transmission for each pixel，the signal to reduce 24bit. pixel adopt auto reshaping transmit technology, making the pixel cascade number is not limited the signal transmission, only depend on the speed of signal transmission.This product uses SMD5050 single-color LED chip instead of RGB chip to realize the digital effect of white light.Can be more appropriate to the needs of customers.LED with low driving voltage, environmental protection and energy saving, high brightness, scattering angle is large, good consistency, low power, long life and other advantages. The control chip integrated in LED above becoming more simple circuit, small volume, convenient installation.

GDC WS2812 Led Strip Features:

GDC WS2812 LED Strip Features:

·Control circuit and RGB chip are integrated in a package of 5050 components, form a complete control of pixel point.

·Built-in signal reshaping circuit, after wave reshaping to the next driver, ensure wave-form distortion not accumulate.

·When the refresh rate is 30fps, low speed model cascade number are not less than 512 points, high speed mode not less than1024 points. Send data at speeds of 800Kbps.

·2/3 OZ FPC, original high quality 3M 9495LE tape, special design strong packing. The LEDs are LM-80 tested and certified.

·Provide customized service, customized MOQ>500M, 3 years warranty.

1. An internal oscillator for timing and changing states a signal reshaping and amplification circuit to make sure the signal is passed to the next LED in the chain

2. A data latch — this holds the state of the particular LED

3. Channel programmable constant output drives (constant current) to control each of the LEDs (red, blue, and green)

4. Digital ports/serial in and serial out to receive and transmit information.

5. This product uses SMD5050 single-color LED chip instead of RGB chip to realize the digital effect of white light.Can be more appropriate to the needs of customers.

bars, commercial buildings, billboards, theme parks, LED screen,etc.

·Never bend the LED strip more than R = 60 mm.

·Installation must not damage parts of the circuit board!LED strips are fine electronics and must be treated carefully.

·The LED strip is divided into sections with scissors symbol where it is possible to cut the LED strip. Cut LED strip of sharp scissors and always at 90°.

·When soldering the strip, the soldering temperature maximum of 300°C. Follow the polarity closely.

·1- When cutting the strip, use a shrink stocking. Remove 3M tape on the part to be "shrunk"

2-Place the shrink stocking over the LED strip.

3-Use a heat gun!

·Depending on the desired assembly, it may be necessary to point glue IP65 LED strips for permanent fastening. Remember that the substrate must be clean!

·All Glite Led Strips is dimmable by 0/1-10V,DALI,PWM,DMX controller.

·Connect Led 12v/24v to positive on driver, conenct Led - to negative on driver.

·LED must work under correct voltage,never work with incorrect driver voltages!

·Take the led strips from reels and open it before test the light with the driver!

Fast Connectors: