5V 60leds/m RGBW Digital SK6812 LED Strips GL-FBSK6812RGBW60M10W5

1.SK6812 SMD5050 Digital LED Strip ,DC5V,60led/m,magic RGBW digital,SDCM<5;

2.Indoor lighting IP20 and outdoor lighting IP65&IP67&IP68;

3.From 4.8w to 18w adjustable wattage;

4. With standard 3M self-stick , easy for installation;

5. CE Certificated and RoHS compliant;

6. Factory wholesale cost.OEM and ODM service.

SK6812 is a smart LED control circuit and light emitting circuit in one controlled LED source, which has the shape of a 5050 LED chip. Each lighting element is a pixel, and the intensities of the pixels are contained within the intelligent digital interface input. The output is driven by patented PWM technology, which effectively guarantees high consistency of the color of the pixels. The control circuit consists of a signal shaping amplification circuit, a built-in constant current circuit, and a high precision RC oscillator.

The data protocol being used is unipolar NRZ communication mode. The 24-bit data is transmitted from the controller to DIN of the first element, and if it is accepted it is extracted pixel to pixel. After an internal data latch, the remaining data is passed through the internal amplification circuit and sent out on the DO port to the remaining pixels. The pixel is reset after the end of DIN. Using automatic shaping forwarding technology makes the number of cascaded pixels without signal transmission only limited by signal transmission speed. The LED has a low driving voltage (which allows for environmental protection and energy saving), high brightness, scattering angle, good consistency, low power, and long life. The control circuit is integrated in the LED above.

GDC SK6812 Led Strip Features:

GDC SK6812 LED Strip Features:

·Top SMD internal integrated high quality external control line serial cascade constant current IC;Gray level adjusting circuit (256 level gray scale adjustable);

·Control circuit and the RGB chip in SMD 5050 components, to form a complete control of pixel, color mixing uniformity and consistency;Built-in data shaping circuit, a pixel signal is received after wave shaping and output waveform distortion will not guarantee a line;

·Data transmission frequency up to 800Kbps, when the refresh rate of 30 frames per second, a cascade of not less than 1024;Line data transmission;

·2/3 OZ FPC, original high quality 3M 9495LE tape, special design strong packing. The LEDs are LM-80 tested and certified.

·Provide customized service, customized MOQ>500M, 3 years warranty.

1. Environmental protection and safety: high-quality high-brightness SMD 5050 LED is used. It has the characteristics of low power consumption, low heat generation, no glare, and impact resistance. Low voltage DC 5V power supply, high safety and reliability.

2. The colors are rich and varied and can be adjusted arbitrarily through the controller according to customer needs.

3. Long lifespan: The average lifespan is 50,000 hours.

4. Convenient and free cutting and welding: each group of LEDs can form a loop, which can be arbitrarily cut and welded along the tangent line (marking) above to meet the needs of various light bar lengths required by customers.

5. Soft: The soft FPCB board is used as the substrate, which can be docked, bent, cut and fixed on the concave and convex surface at will.

6. Light and thin: suitable for installation in narrow spaces.

bars, commercial buildings, billboards, theme parks,etc.

·Never bend the LED strip more than R = 60 mm.

·Installation must not damage parts of the circuit board!LED strips are fine electronics and must be treated carefully.

·The LED strip is divided into sections with scissors symbol where it is possible to cut the LED strip. Cut LED strip of sharp scissors and always at 90°.

·When soldering the strip, the soldering temperature maximum of 300°C. Follow the polarity closely.

·1- When cutting the strip, use a shrink stocking. Remove 3M tape on the part to be "shrunk"

2-Place the shrink stocking over the LED strip.

3-Use a heat gun!

·Depending on the desired assembly, it may be necessary to point glue IP65 LED strips for permanent fastening. Remember that the substrate must be clean!

·All Glite Led Strips is dimmable by 0/1-10V,DALI,PWM,DMX controller.

·Connect Led 12v/24v to positive on driver, conenct Led - to negative on driver.

·LED must work under correct voltage,never work with incorrect driver voltages!

·Take the led strips from reels and open it before test the light with the driver!

Fast Connectors: