12V 60leds/m RGB Digital TM1934 LED Strips GL-FBTM1934RGB60M10W12

1.TM1934 SMD5050 Digital LED Strip ,DC12V,60led/m,magic RGB digital,SDCM<5;

2.Indoor lighting IP20 and outdoor lighting IP65&IP67&IP68;

3.From 4.8w to 18w adjustable wattage;

4. With standard 3M self-stick , easy for installation;

5. CE Certificated and RoHS compliant;

6. Factory wholesale cost.OEM and ODM service.

TM1934 LED RGB strip have more than 16 million colors of light, and various colors or transformations can be customized according to requirements, and any animation effect of the product can be realized through the programming of the external controller. The external breakpoint resume TM1934 drive core adopts low-voltage DC12V power supply, and the design of double SPI signal data lines in series can realize the function of breakpoint resume transmission.

GDC TM1934 Led Strip Features:

GDC TM1934 LED Strip Features:

· Using a soft FPC board as the substrate, FPC has good electrical conductivity, fast heat dissipation, bending resistance, can be arbitrarily bent, can be docked, bent, cut and arbitrarily fixed on the concave and convex surface.

· High-quality super bright LED light-emitting diodes are used to emit light, with low power consumption, low heat, no glare, impact resistance, etc.; low-voltage 12V power supply, safe and reliable.

· There are more than 16 million colors of light, and various colors or transformations can be customized according to requirements, and any animation effect of the product can be realized through the programming of the external controller.

· Small and thin, suitable for installation in narrow spaces.

· The external breakpoint resume TM1934 drive core adopts low-voltage DC12V power supply, and the design of double SPI signal data lines in series can realize the function of breakpoint resume transmission.

· Free cutting, every three LEDs can form a loop, which can be arbitrarily cut off and welded along the tangent above to meet the needs of various light bar lengths required by customers.

·2/3 OZ FPC, original high quality 3M 9495LE tape, special design strong packing. The LEDs are LM-80 tested and certified.

·Provide customized service, customized MOQ>500M, 3 years warranty.

1. TM1934 is a dedicated circuit for single-wire three-channel LED constant-current drive. It can switch inputs to each other through two-channel digital interface (DIN, FDIN), and cascade with DO port. The external controller can control the chip with only one wire.

2. The chip integrates MCU single-wire dual-channel digital interface, data latch, LED constant current drive, PWM brightness control and other circuits.

3. The 5V voltage regulator tube is integrated inside the VDD pin, and there are few peripheral devices.

bars, commercial buildings, billboards, theme parks, LED screen,etc.

·Never bend the LED strip more than R = 60 mm.

·Installation must not damage parts of the circuit board!LED strips are fine electronics and must be treated carefully.

·The LED strip is divided into sections with scissors symbol where it is possible to cut the LED strip. Cut LED strip of sharp scissors and always at 90°.

·When soldering the strip, the soldering temperature maximum of 300°C. Follow the polarity closely.

·1- When cutting the strip, use a shrink stocking. Remove 3M tape on the part to be "shrunk"

2-Place the shrink stocking over the LED strip.

3-Use a heat gun!

·Depending on the desired assembly, it may be necessary to point glue IP65 LED strips for permanent fastening. Remember that the substrate must be clean!

·All Glite Led Strips is dimmable by 0/1-10V,DALI,PWM,DMX controller.

·Connect Led 12v/24v to positive on driver, conenct Led - to negative on driver.

·LED must work under correct voltage,never work with incorrect driver voltages!

·Take the led strips from reels and open it before test the light with the driver!

Fast Connectors：