12V 144leds/m RGB Digital WS2815 LED Strips GL-FBWS2815RGB144M12W12

1.WS2815 SMD5050 Digital LED Strip ,DC12V,144led/m,magic RGB digital,SDCM<5;

2.Indoor lighting IP20 and outdoor lighting IP65&IP67&IP68;

3.From 4.8w to 18w adjustable wattage;

4. With standard 3M self-stick , easy for installation;

5. CE Certificated and RoHS compliant;

6. Factory wholesale cost.OEM and ODM service.

WS2815 is an intelligent control LED light source that the control circuit and RGB chip are integratedinapackageof 5050 components. Its internal includes intelligent digital port data latch and signal reshaping amplificationdrivecircuit. Dual-signal wires version, signal break-point continuous transmission. Any pixel’s failure won't affect signal transferand total emitting effect.

GDC WS2815 Led Strip Features:

GDC WS2815 LED Strip Features:

· The control circuit and RGB chip are integrated in a 5050 components, to form an external control pixel.

· 12V DC power supply, can effectively reduce the operating current of the pixel LED, and decrease the voltage-dropof the PCB, this is to advance the consistency of the mixed lights for long-distance transmission.

· Using the built-in signal reshaping circuit to achieve the signal waveform shaping, and no distortion of waveformofsignal takes place.

· The gray levels of each pixel are of 256 levels, which achieves “256*256*256=16777216” full-color display, andthe refresh frequency reaches to 2KHz.

· Serial cascade interface, data receiving and decoding depend on just one signal line.

· Dual-signal wires version, signal break-point continuous transmission.

· Any two point the distance more than 5M transmission signal without any increase circuit.

· When the refresh rate is 30fps, cascade numbers is at least 1024 pixels.

· Data transmitting at speeds of up to 800Kbps. l

· Good color consistency reliability, high cost-effective.

· 2/3 OZ FPC, original high quality 3M 9495LE tape, special design strong packing. The LEDs are LM-80 tested and certified.

· Provide customized service, customized MOQ>500M, 3 years warranty.

1. WS2815 LED strip is an upgraded version of the 5V WS2812B LED strip. For the 5M LED strip, even if all the LEDs are turned on full white, the 12V version has no voltage drop. You don't need to inject power as frequently as the 5V version.

2. Each pixel can have its own color and brightness. You can control it individually and set them to any color or animation you want. 256 brightness display and 24-bit color display.

3. WS2815 LED strip is Similar to the version of the 5V WS2813 LED strip, Designed with one data wire and one backup data wire. Signal break-point continuous transmission. If one LED is damaged, the following LEDs can still work.

bars, commercial buildings, billboards, theme parks, LED screen,etc.

·Never bend the LED strip more than R = 60 mm.

·Installation must not damage parts of the circuit board!LED strips are fine electronics and must be treated carefully.

·The LED strip is divided into sections with scissors symbol where it is possible to cut the LED strip. Cut LED strip of sharp scissors and always at 90°.

·When soldering the strip, the soldering temperature maximum of 300°C. Follow the polarity closely.

·1- When cutting the strip, use a shrink stocking. Remove 3M tape on the part to be "shrunk"

2-Place the shrink stocking over the LED strip.

3-Use a heat gun!

·Depending on the desired assembly, it may be necessary to point glue IP65 LED strips for permanent fastening. Remember that the substrate must be clean!

·All Glite Led Strips is dimmable by 0/1-10V,DALI,PWM,DMX controller.

·Connect Led 12v/24v to positive on driver, conenct Led - to negative on driver.

·LED must work under correct voltage,never work with incorrect driver voltages!

·Take the led strips from reels and open it before test the light with the driver!

Fast Connectors: